How to Not Suck at Cornering

September 24, 2014

How to Not Suck at Cornering

Hot on the heels of the The Power of the Quick Turn article is this followup post about what happens after you tip into a corner. Too many riders struggle with cornering, not necessarily because they are afraid to lean, but becasue they do not understand how to properly complete a turn.

Cornering Basics

By now you know that motorcycles must lean to change direction and that leaning is done by countersteering. Read about countersteering HERE.
Once the bike begins to lean, countersteering pressure is reduced and other dynamics take over that cause the motorcycle to arc around the curve, including front end rake and trail geometry, as well as something called camber thrust. Camber thrust is the term that describes how a tapered object (a motorcycle tire leaned over) orbits around its axis when rolling along a surface (the pavement).
In other words, the rounded profile of a motorcycle tire acts like a tapered styrofoam cup when it’s rolled on its side. Give it a push and it rolls in a circle.
Here is how author and fellow USCRA racer Tony Foale describes camber thrust:
“As the inside edge of the tyre is forced to adopt a smaller radius than the outer edge, then for a given wheel rotational speed, the inner edge would prefer to travel at a smaller road speed, this happens if the wheel is allowed to turn about a vertical axis through the point of the cone. Just as a solid cone on a table if given a push.”
For our purposes, all you really need to understand is that your motorcycle is designed to track around a curve with minimal effort once the bike is in a lean. Front end geometry (caster effect, rake, trail, etc.) all make this possible. If you want to read more, go to Tony Foale’s website and learn all about it.
If your bike is properly maintained and has relatively new tires with nearly the original profile intact, you should be able to initiate lean and then maintain that lean angle without introducing any significant handlebar inputs. Problems occur when the rider messes this process up. Most bikes will track predictably and with little effort as long as the rider doesn’t interfere with the process or introduce counterproductive inputs.

Variations in Machine Design

Some riders insist that they cannot round a corner without using significant handlebar pressure to keep their machine on the desired path. Instead of being able to relax and let the bike carve the path, they fight the bars all the way around the curve. It is possible that the machine is to blame, but these days this is rarely true.
While I have ridden bikes with really bad cornering dynamics, the vast majority of modern machines offer balanced, neutral handling that requires little-to-no mid-corner intervention. The only reason for handlebar adjustments are because of mid-corner changes in turn radius, camber or surface condition. A smooth constant radius curve, ridden well, requires almost no additional handlebar pressure.
It’s important to note that different types of bikes handle differently. Sportbikes are responsive to steering inputs, while cruisers tend to be slower steering, but more stable. Still, if the rider does all the right things, then the differences in machine does not make that much of a difference. The trick is to have the knowledge and skill to complete a corner proficiently.
Basically, it’s usually much more productive to evaluate the user instead of blaming the machine.

User Error

To repeat…once the necessary lean angle is established, most bikes are happy to track around a corner with little effort. So, why do some riders struggle with this part of the cornering process? The answer lies in a few areas.

Tension at the handlebars. The front of the bike needs to be free to move up, down, and side -to-side in response to both large and small changes in the road surface. Being stiff on the handlebars interferes with this motion and causes the motorcycle to feel reluctant to turn. It also asks the tires to work harder to stay in contact with the surface. Another problem with stiff arms is that you are inhibiting the slight countersteering corrections that may need to occur to deal with changes in camber or other variations in corner surface. Loose arms allow fluid reactions.
Poor body position. Think of your bike as your dance partner who wants you to lead. In the case of the cornering dance, a slight dip of the shoulder to the inside of the curve will encourage smoother cornering. In contrast, a rider who stays upright or leans outside is stepping on the bike’s toes, causing it resist fluid cornering.
Not using the Throttle Correctly. For the motorcycle to track around the corner predictably and smoothly, the suspension must be stable and in the middle of its travel. Smooth, gradual acceleration throughout the curve produces the best results. Be sure to slow enough at the beginning of turns so that you can comfortably roll on the gas all the way to the exit. Unfortunately, a lot of riders fail to use steady throttle in corners. This is a problem, because changes in speed and drive force alter the arcing path the motorcycle takes. Abruptly chopping on or off the throttle upsets this stability and causes the bike to lift and fall in and out of the established angle of lean and introduces forces that result in a wobbly or weaving line around the corner. Note that acceleration typically makes the bike drift wide and deceleration can either cause the bike to drop into the corner more or cause it to stand up, depending on how abruptly the throttle is chopped and how the machine /tire combo responds to this input.
Not Looking through the Turn. You tend to go where you look, so look where you want to go! By keeping your visual attention through the turn and toward the corner exit, your mind is able to better manage the corner. The other advantage is that the landscape slows down when you look ahead. This reduces anxiety and helps complete the concerning process. Looking ahead will not suddenly make you a cornering master, but without habitually looking ahead, you will never become one. Keep your eyes up.

Cornering Technique

Okay, so let’s break it down.

Look well ahead.
Countersteer to initiate lean for the corner.
Crack the throttle as soon as the bike is leaned. Use gentle drive at first and then progressively feed in more drive force. Roll on with more authority as lean angle is reduced near the corner exit. Steady drive creates steady cornering.
Relax! If you established the correct angle of lean for the turn, the bike should require only slight adjustments in handlebar pressure. Corners that tighten will require you to press more on the inside bar to lean the bike more, but keep the throttle as steady as possible.
Finish the turn. You’re not done yet. Keep looking toward the corner exit and roll on the throttle a bit more to let the bike drift toward the outside of the curve. This facilitates the “outside-inside-outside” cornering line, which I will discuss in a future post.
Rinse and repeat for the next corner.

There is so much more to learn about the cornering process, but this is a good start. Implement these steps and you’re well on your way to becoming a cornering master.
What tips can you share that help you to corner with more confidence?

Please Donate to Keep the Articles Coming

If you liked this article and the many other articles on this site, please toss a buck or five into the hat. It’s greatly appreciated!

- Click the PayPal “Pay Now” button.
- Then indicate quantity in $2.00 increments. – Example: put “2” in “QUANTITY” field to donate $4.00, “3” for a $6.00 donation, etc.

Why $2.00? Due to the PayPal fee structure, a $2.00 donation is significantly more beneficial compared to a $1.00 donation.

Thank You!

Check out these related posts:

Stay Informed: Subscribe NOW!

Be a Better Rider: Sign Up for Personal Training with Ken

Support Riding in the Zone: Buy a book

Support Riding in the Zone: Buy products from Twisted Throttle & Amazon

September 17, 2014

The Power of the Quick Turn

Ken, turning-in hard and precisely. www.owenstrackdayphotos.com — Ken, turning-in hard and precisely.
www.owenstrackdayphotos.com

Most motorcycle riders initiate lean in a somewhat lazy manner. In most cornering situations and at normal street speeds it is perfectly fine to gradually ease into a corner with light pressure on the handlebars. But, when the pace picks up and the corners become less predictable, a sluggish, indecisive turn-in will cause you to run wide at corner exits. The ability to turn quickly gives you a survival tool for managing misjudged corners while also increasing an overall sense of control and confidence. Booya!

Cornering 101

Before we get into quick turning technique, you must understand the basics of how a motorcycle changes direction. Motorcycles must lean to turn. Leaning is done primarily by introducing countersteering pressure on the handlebar: press forward/down on the handlebar on the side in which you want to turn.
Not sure you understand countersteering? Read This Article NOW. FYI, you can quicken steering by pushing on the inside handlebar while also pulling on the opposite bar.

How Quicker Turns Help

Turning the motorcycle within a shorter distance and period of time gets the bike to change direction early. The quicker the bike is leaned, the earlier the direction change is completed, which affords you a greater margin of error to handle a misjudged turn radius or a slightly overspeed entry. Look at the diagram and you’ll also see that a quicker turn-in means you are not leaned over as long.
Another benefit of a quick turn is that it allows the bike to reach maximum necessary lean angle before or at the turn apex (the innermost part of the corner), which means that you can get on the gas sooner for both greater corner stability (bikes like being under drive when cornering) and greater exit speed (for you performance riders): Tip-in and then crack the throttle.

A quicker turn allows early direction change and less risk of an on-throttle highside. — A quicker turn allows early direction change and less risk time at full lean angle.

A delayed apex requires a delayed, quick turn-in.

Quick Turns and Cornering Lines

The quick turn technique can be used for most, but not all corners. Some corners are laid out so that a gentle, sweeping entry is best. But, most other corners benefit from a quick turn, especially turns we call “exit” turns that require a slower entry and an early drive out of the corner.
A quick turn is also useful as a way to achieve a delayed apex cornering line. Delaying turn-in by a half-second or so keeps you outside a bit longer at the turn entry for a wider angle of view and points the motorcycle toward the turn exit, rather than toward the outside edge of the lane. Novice riders often dive for the inside of a corner as they react to anxiety about not being able to make the turn. This can easily result in an early apex and a blown exit. Ouch!
Instead, wait for it, wait for it…okay, turn, NOW.

Quick Turning and Traction

As you might imagine, giving the handlebar a good shove introduces an abrupt force to the front tire. That’s why you want to limit using the quick turning technique when traction is limited, such as on wet or contaminated pavement. A quick turn uses more traction at the beginning of the turn, but uses less at the apex and exit. Even though more traction is used when turning quickly, good tires in dry conditions have more than enough grip to handle the extra force.
To minimize the risk of tucking the front tire, you must get most of your braking done and start easing off the brakes before you introduce forceful handlebar inputs. However, it is beneficial to maintain some front brake force as you countersteer, which compresses the front suspension and loads the front tire for more rapid turning response. Ideally, you would release the brakes a split-moment after you press on the handlebars.
I’m talking about releasing the brakes almost immediately after initiating lean. If you want to maintain braking pressure longer (trailbraking), then you’re better off not turning in quickly. To manage traction while trailbraking your turn-in must be gradual, because you’re combining both turning forces and brake forces.

Timing & Intensity

A well-timed quick turn should result in a single handlebar input that establishes necessary lean angle and allows immediate throttle application (very gradual at first).
Turning in too hard and/or too early could result in the motorcycle hitting the inside of the curve. To prevent this, you will need to delay turn-in from where you would begin to turn for a slow turn-in. To fine-tune how rapidly the bike turns in, you can also reduce how hard you press on the handlebars. The harder you press, the more rapidly the bike will fall into the lean.

Practice the quick turn technique in a parking lot. And then apply it on your next ride.

NOW is the Time!

I don’t care if you ride a GSXR on the racetrack or a Harley on the street, you must master the quick turn technique NOW. Being able to use immediate, authoritative handlebar pressure gives you a MUCH better chance of surviving a too fast corner entry. Learning the quick turning technique will allow you to get the bike turned early and efficiently and minimize the chance that you will panic and grab the brakes or run wide into the oncoming lane or off the pavement. Don’t delay! This just might happen on your very next ride!
Learning to turn quickly isn’t difficult, but it does require excellent countersteering skills and precise timing. Turning quicker also requires more forceful handlebar pressure and the trust that the tires will stick under the stress of more forceful handlebar inputs. Practice is what will convince your mind and muscles of the power of the quick turn. Do it!

Please Donate to Keep the Articles Coming

If you liked this article and the many other articles on this site, please toss a buck or five into the hat. It’s greatly appreciated!

- Click the PayPal “Pay Now” button.
- Then indicate quantity in $2.00 increments. – Example: put “2” in “QUANTITY” field to donate $4.00, “3” for a $6.00 donation, etc.

Why $2.00? Due to the PayPal fee structure, a $2.00 donation is significantly more beneficial compared to a $1.00 donation.

Thank You!

Check out these related posts:

Stay Informed: Subscribe NOW!

Be a Better Rider: Sign Up for Personal Training with Ken

Support Riding in the Zone: Buy a book

Support Riding in the Zone: Buy products from Twisted Throttle & Amazon

September 10, 2014

Guest Writer: When Do You Lean?

The ability to lean a motorcycle with confidence is a fundamental part of riding. Unfortunately, humans do not come hardwired to lean much more than about 20 degrees, which is the lean angle where we start to lose traction when we run in a circle on grass or dirt. Motorcycle riders must get beyond this lean angle limit for even basic maneuvers. This requires a leap of faith that the tires will grip. Practice is important to train your mind and muscles to lean beyond your comfort zone so you will be able to lean more if necessary. Once greater lean angles become more comfortable, the next skill to refine is timing so you reach maximum lean angle at the right point in the corner.

Paul Duval at full lean.www.otmpix.com — Paul Duval at full lean. www.otmpix.com

Meet Paul Duval

Paul Duval is the latest RITZ guest writer. Paul is a fellow track day and MSF instructor, former Loudon Road Racing Series 125 GP Champion, and professional educator. Let’s listen to Paul’s take on the importance of accurately timing maximum lean angle.

Timing Maximum Lean Angle

After many years of racing and instructing on the racetrack, there is one persistent mistake I see riders make when trying to ride faster: Using too much lean, too late in the corner.

Who is making this mistake?

Everyone is susceptible to this problem. Novice and intermediate track day riders often make the mistake of increasing lean angle late in the corner in an attempt to get their knee down. Especially vulnerable riders are those with a lot of “natural talent” who got fast so much more quickly than everyone else. They end up riding fast, but without the knowledge and precision necessary to manage that corner speed.

What’s the Problem?

Adding throttle and increased lean angle at the same time is a bad idea.

You may say, “What’s the big deal, I’m knee down and cranking?!” Yes, you may be fast, but this mistake WILL eventually lead to a crash, and probably a BIG one.
The problem with reaching max lean angle well after the apex of a turn is that this is precisely where you want to be on the gas. Other riders will be already picking the bike up and driving hard. This will encourage you to match their drive, but you are still adding lean angle.
Remember this: Adding lean angle AND throttle at the same time is how high sides happen. The opposing forces of changing direction and accelerating can easily exceed available traction and will cause the rear tire to slide. When this happens, slides are extremely quick, unpredictable, and hard to recover from. All of your momentum is going exactly the wrong way.

Why do I keep doing this?

There are a few reasons people make this mistake.
– Weak countersteering skills: Newer riders haven’t yet mastered the “quick turn” technique of using counter steering to get the bike leaned over. They bend their motorcycle into the turns gradually and often pass the apex entirely before the bike has changed direction. Now they are running out of real estate and HAVE to lean it over to finish the turn.
– Lack of reference points:Beginner and Intermediate track riders often use other riders as their reference points. This leads to a lot of crazy entry lines, none of which help the rider get the bike to change direction before the apex. They commonly ride around the entry point as well as the apex, then crank the bike over to finish the turn.
– Charging the corners: Faster riders who make this mistake are at the most risk. They rush into the corner at a pace that does not allow them to consistently hit their marks. They will blow by a tip in point, drift wide past the apex, and then attempt to recover to get back on the “fast” exit line by adding a little more lean and a little more throttle.
Even with all this effort, they wonder why the faster guys are still pulling away. They aren’t even cranked over like I am!!! Hmmmm??? You may get away with late lean angles for a while, but eventually, you will push this mistake too far. Highside city.

The Solution?

The correction for all these riders is pretty similar. And it’s not what they want to hear: SLOW DOWN your corner entry to a speed that you can actually handle. I mean a speed at which you can identify reference points, and ride an accurate line from tip in to apex that allows you to OPEN the corner after the apex, rather than tighten it up. You need to learn to time your throttle inputs and your lean angle so that as you drive out of the corner and standing the bike up progressively as you roll on the gas. BRAAAAP! Wheee!

Ken:
Thanks Paul. Paul mentioned the importance of being able to turn quickly. By being able to countersteer with authority, you are able to get your motorcycle from upright to leaned so that the majority of the direction change is complete BEFORE the apex. With the change in direction mostly complete, you can reduce lean angle as you roll on the gas. Traction is managed and all is well. Post your comments below.

Please Donate to Keep the Articles Coming

If you liked this article and the many other articles on this site, please toss a buck or five into the hat. It’s greatly appreciated!

- Click the PayPal “Pay Now” button.
- Then indicate quantity in $2.00 increments. – Example: put “2” in “QUANTITY” field to donate $4.00, “3” for a $6.00 donation, etc.

Why $2.00? Due to the PayPal fee structure, a $2.00 donation is significantly more beneficial compared to a $1.00 donation.

Thank You!

Check out these related posts:

Stay Informed: Subscribe NOW!

Be a Better Rider: Sign Up for Personal Training with Ken

Support Riding in the Zone: Buy a book

Support Riding in the Zone: Buy products from Twisted Throttle & Amazon

August 22, 2014

Guest Writer: Just Go Faster

Jeff Meyers on his '05 ZX6R — Jeff Meyers on his ’05 ZX6R www.otmpix.com

“Just go faster, Jeff,” my track riding guru Ken Condon says after asking him what I need to do next as a track day rider. I am flattered, because Ken says that my track form is very good. He says that I am on “the line,” I am riding predictably and smoothly, and my body position, while I am sure it can be tweaked, is getting much better.
However, I am also befuddled because I wish it were that simple to “just go faster.” The problem is that each time I enter a turn faster than before, alarm bells shriek in my head, and adrenaline courses through my system. A voice screams “You are going waaaaay too fast for this corner!!” I am terrified.

Speed is the Result of Good Technique

Ken tells me that a faster pace is the result of good technique and consistency. So, I discipline myself to look farther down the track, keep maintenance throttle, relax my hands and upper body, and make my bike lean a little farther, all while being mindful not to move too much so that I don’t upset the suspension or cause tire slip. It’s a balancing act, a tightrope on two wheels. I am terrified, and yet I am so happy at the same time.

Take the Time You Need

I’m not exactly a rookie to track riding. I have done fifteen track days total, all with Tony’s Track Days. Up until now, I have spent my time in the novice (Red) group, often debating whether I was ready to bump up to the intermediate (Yellow) group. I decided to stay in the novice group longer than I needed to so I could cement the basics and eliminate bad habits at relatively slower speeds. I also wanted to learn how to pass safely and courteously.

The lucky new owner of the ZX6R. I hope you enjoy it as much as I have. — Jeff Meyers

My ego didn’t like it, but I kept telling my ego to shut the hell up because my body didn’t want to pay the price of crashing. It worked. I am now a solid “Yellow Rider” and feel confident that I am there with the appropriate skill set. Ironically, “yellow” is an appropriate description for my current level since fear is now the main factor holding me back from going faster.
Over the next several track days, I plan to fine-tune my form, push myself against that fear barrier, and (hopefully) build confidence each time so that I become consistently faster. My goal is to bump up to the Advanced (Blue) group, and who knows, maybe to the Super-advanced (Black) group someday.

Jeff Meyers is the newest guest blogger to the RITZ team. Jeff is a self-described middle-aged sport bike and track day dog. He has been riding for almost 30 years and, like many folks of his vintage, was taught by his friends. He is amazed to still be here given what he did at a young age on a motorcycle with such little skill and such a need for speed. He is a lawyer at his “real” job, but also is a part time Motorcycle Safety Foundation Rider Coach and has had the privilege of working for Suzuki assisting in running demo rides, mostly at the Americade rally in Lake George, New York. Jeff loves to learn, especially about riding motorcycles.

Thanks, Jeff. I’m sure you will meet your goal of moving into the faster groups. Just continue to take the time you need to get there.
What are your riding goals? What holds you back from accomplishing them?

Please Donate to Keep the Articles Coming

If you liked this article and the many other articles on this site, please toss a buck or five into the hat. It’s greatly appreciated!

- Click the PayPal “Pay Now” button.
- Then indicate quantity in $2.00 increments. – Example: put “2” in “QUANTITY” field to donate $4.00, “3” for a $6.00 donation, etc.

Why $2.00? Due to the PayPal fee structure, a $2.00 donation is significantly more beneficial compared to a $1.00 donation.

Thank You!

Check out these related posts:

Stay Informed: Subscribe NOW!

Be a Better Rider: Sign Up for Personal Training with Ken

Support Riding in the Zone: Buy a book

Support Riding in the Zone: Buy recommended products from Twisted Throttle & Amazon

July 11, 2014

Ground Clearance & Grip

Cornering on a big cruiser requires a respect for clearance limits.

I just received another letter from a Motorcycle Consumer News reader, this time about a situation he encountered when riding on a twisty back road in Cali on his Street Glide. Here’s his story, followed by my response.

“Ken, your recent article (in Motorcycle Consumer News) on cornering traction was excellent. I just returned to Las Vegas after traveling up the coastal hwy to Oregon then back down to Las Vegas. While on that trip I had an incident involving cornering that left me very puzzled.
While heading to the coast from the 101 on hwy 128 north of San Francisco I was enjoying the curves of the coastal range. I ride a Harley Street Glide and ride fairly aggressively but not what I consider unsafe. As I was entering one turn (posted at 20mph) I leaned the bike into the turn and suddenly heard metal screeching on asphalt and almost simultaneously was aware that I had lost traction and was heading for the outside of the corner and a steep drop off.
Automatically I jammed my left foot down to the asphalt, but with my speed around 30-40mph sprained my ankle pretty badly. Much to my surprise I regained traction on the outside of the corner and was able to hold it there through the last 1/2 of the corner. My conundrum is that I’m not sure what happened! I felt comfortable with the speed I had entered the corner and I had entered from wide to just inside the center lane when the incident occurred. Normally, if I’m leaning the bike too much I’ll be aware of the foot board dragging. In this case there was no warning, just metal screeching and loss of traction simultaneously. Also, the road was great, with fairly new asphalt and no noticeable debris. Your thoughts would be greatly appreciated as this incident has made me extremely apprehensive whenever entering a corner with thoughts of this incident constantly in the back of my mind.”

Fairly aggressive cornering on a cruiser can be done, if you respect the bike's limits. — Fairly aggressive cornering on a cruiser can be done, if you respect the bike’s limits.

My Response

Without having seen or experienced the actual incident, I can only speculate on the cause based on knowledge of typical scenarios like yours. The fact is that ground clearance just doesn’t go from sufficient to nonexistent without a reason. It could be that you were leaning far enough that you were about to touch your floorboard when the mysterious factor occurred and your bike was suddenly grinding hard parts. This levered your tires off the ground and reduced traction.
Most times, when a bike suddenly goes from adequate ground clearance to zero ground clearance, it is a sign of traction loss caused by undetected surface contamination or debris, or abrupt throttle, brake or handlebar inputs, all of which are rider error. Sudden traction loss while the bike is leaned will cause the bike to drop quickly. This usually results in the rider tensing on the handlebars and chopping off the throttle, which exacerbates the problem.
If neither surface debris nor rider error existed, then you have to look at the possibility of a sudden and undetected change in surface camber that reduces ground clearance, or perhaps a depression in the road that would cause the suspension to compress.
Predicting that conditions can change quickly is a key survival strategy and applies to seemingly perfect pavement. New pavement can actually make ground clearance-robbing features such as undulations and dips difficult to see.
Knowing that your bike is a low slung machine means that you must be particularly sensitive and aware of these clearance hazards so that they don’t cause problems. One way to help manage limited ground clearance is to slow down.

Hanging off the inside of the bike helps increase clearance.

You can also learn to use body positioning to help increase ground clearance. By simply dropping your head and shoulder to the inside, you shift the combined center of gravity of bike and rider so that your machine doesn’t have to lean quite as much. Practice this in a parking lot and notice that your floorboards don’t drag as readily. My book has drills that can help.
If you are riding briskly on your Street Glide and continue to have clearance problems, perhaps you are exceeding the limits of the bike and need to consider trading in for a model that is more suited to your cornering exuberance.
Now that we’ve discussed the possible cause, let’s look at your reaction. The sudden loss of ground clearance, for whatever reason, triggered a panic response that not only had no significant effect on allowing your big Harley to recover traction, but also caused you to injure your ankle. This panic response is part human nature and is how most riders react when faced with a potentially life threatening situation.

Off-road riding helps train for minor traction loss events.

To minimize these survival instincts from causing more harm, you would need to re-train your mind and body to feel okay with minor traction loss. This is not easy to do when you ride a road-going cruiser, but is easily achieved with some off-road riding experience. Off-road riders routinely experience wide variations in traction and become accustomed to traction loss so that they do not overreact and make matters worse.
But, please understand that training yourself to react correctly is not a substitute for being aware of hazards and preventing them from causing an incident from happening in the first place.

The results of overriding a bike's capabilities can be disastrous. — The results of overriding a bike’s capabilities can be disastrous.

I hope this helps.
Ken

Do you have anything to add? Have you encountered a similar situation? How did it turn out? Please comment below.

Please Donate to Keep the Articles Coming

If you liked this article and the many other articles on this site, please toss a buck or five into the hat. It’s greatly appreciated!

- Click the PayPal “Pay Now” button.
- Then indicate quantity in $2.00 increments. – Example: put “2” in “QUANTITY” field to donate $4.00, “3” for a $6.00 donation, etc.

Why $2.00? Due to the PayPal fee structure, a $2.00 donation is significantly more beneficial compared to a $1.00 donation.

Thank You!

Check out these related posts:

Stay Informed: Subscribe NOW!

Be a Better Rider: Sign Up for Personal Training with Ken

Support Riding in the Zone: Buy a book

Support Riding in the Zone: Buy recommended products from Twisted Throttle & Amazon

July 8, 2014

The "No Countersteering" Myth

A MCN reader recently wrote telling about his enthusiasm for Reg Pridmore’s “body steering” method of initiating lean for cornering. What follows is my response.

“I have 44 years experience riding and currently ride six days a week commuting and sport riding. Three years ago I read Smooth Riding the Pridmore Way by Reg Pridmore. This book completely changed my knowledge of corning a bike. For years I subscribed to countersteering as noted in this article. The Pridmore way is to body steer the bike and keep your upper body relaxed and smoothly controlling throttle, clutch, and brake. It took me a few months to re-learn corning, but now I am much more proficient and safe on the bike. His book goes into the details why this is better and how to master these skills. It is my opinion that there is an alternative to countersteering and I feel it is much safer to use the geometry of the bike versus fighting the physics of corning with the handlebars. “

My response:

This discussion has been going on for over a decade and has even sparked an Internet rivalry between Pridmore and Keith Code, who advocates and emphasizes countersteering as part of the California Superbike School as the best way to initiate lean. Having ridden the CSS No BS bike (which has handlebars mounted rigidly to the frame with a working throttle), I can confidently tell you that body “steering” alone will not allow a rider to corner in any meaningful or effective way on a 400 to 800 pound machine. See the video of Code riding the No BS bike to see how little body position has on direction control.
Yes, body “english” can enhance many aspects of cornering process. I am a very big proponent of body positioning for both street and track riders to aid quicker turning, refine cornering lines, increase ground clearance, preserve traction, and allow the rider to interact more with the bike and the road. But, body positioning alone cannot cause the average street bike to initiate a corner efficiently or quickly enough. That is done by countersteering.
Countersteering uses the geometry of the bike to essentially unbalance the machine, causing it to drop into a lean. There are many other aspects of the process, but that’s all most riders need to know. You mention the other important aspect of masterful cornering, which is relaxing the arms as much as possible once the lean is initiated and using smooth control inputs to maintain control.
I have no doubt that your revelation and enthusiasm for Reg Pridmore’s fine book and teachings are genuine, but I can guarantee that you are using countersteering (in combination with body positioning) to lean your bike into a corner. What is happening is you have replaced some of the “handlebar only” countersteering inputs you have used routinely for many years with a body position technique that is “pre-loading” the bike for the corner.
This shift in the center of gravity causes the bike to fall into the turn easier, making it feel as if you are not putting any pressure on the handlebars. This is a technique taught by Lee Parks in his Total Control curriculum and which I teach to track day students. Next time you go for a ride, pay very close attention to the amount of pressure you are putting on the handlebars as you initiate lean. If you concentrate enough, you will surely notice that you are introducing handlebar pressure. Because there really is no alternative to countersteering, only reducing the amount of pressure needed.
Additionally, the act of moving your body in the direction of the turn causes handlebar inputs. You would have to consciously resist pulling the outside bar or pressing on the inside bar to eliminate any countersteering force, which would be very difficult to do.
I’m glad you feel more proficient. Keep doing what you’re doing, but you’ll be better off if you know what is really happening. Good luck.
Ken Condon
I received a reply from the reader. He is sticking with his belief that he is not countersteering.
Please share your thoughts below.
Listen to the Countersteering PODCAST

Please Donate to Keep the Articles Coming

If you liked this article and the many other articles on this site, please toss a buck or five into the hat. It’s greatly appreciated!

- Click the PayPal “Pay Now” button.
- Then indicate quantity in $2.00 increments. – Example: put “2” in “QUANTITY” field to donate $4.00, “3” for a $6.00 donation, etc.

Why $2.00? Due to the PayPal fee structure, a $2.00 donation is significantly more beneficial compared to a $1.00 donation.

Thank You!

Check out these related posts:

Countersteering will save your life
California Superbike School No-BS Machine (from the CSS website)

See the video segment about countersteering from the RITZ DVD:

Stay Informed: Subscribe NOW!

Be a Better Rider: Sign Up for Personal Training with Ken

Support Riding in the Zone: Buy a book

Support Riding in the Zone: Buy products from Twisted Throttle & Amazon

May 27, 2014

#1 Reason Why Motorcycles Crash in Corners

Josh, looking good on his Gixxer1000 at Loudon. owenstrackdayphotos.com

Motorcycles crash for many different reasons, including in no particular order:

They are not very stable when ridden slow, so tip overs are common
They are hard to see in traffic, so collisions with cars is far too frequent
They only have two small tire contact patches, so seemingly small things can cause traction loss
They require fairly precise rider decisions and inputs when traction is near its limit
Most single-vehicle crashes are the result of a too-fast corner entry speed.

Case Study

My friend and track day student, Joshua had a problem with numbers 3, 4 and especially 5.
Josh had a great day at the awesome New York Safety Track until he didn’t. Check out his VIDEOS BELOW to see how his day ended. He walked away unscathed, thanks in no small part to his quality riding gear. ATGATT, baby. The same can’t be said for his beautiful GSXR1000. It slid off the track without much fanfare until it hit some protruding piece of Earth and flipped a few times. Oh well. It’s just a machine, remember.

Below, you can read Josh’s account of the situation and what he learned.

Sky, Ground, Sky, Ground. :( — Sky, Ground, Sky, Ground. 🙁

The Fundamental Reason Why He Crashed

Riding a motorcycle is more of a mental exercise than physical. Yes, it takes physical coordination and a certain amount of strength to operate a motorcycle. But, riding a motorcycle well is much more than simply operating the machine. It also includes using excellent judgement and having deep knowledge about how to manage all sorts of situations.
Mark Brown from MotoMark1 uses the term “driving” to emphasize that you must not passively “ride” a motorcycle, but rather “drive” it with purposefulness, authority and competence.
Josh was doing great all day and, as was the case with another rider at the track that day, got over confident and pushed just a little bit harder than he should have. This mental lapse is essentially THE reason Josh crashed. A too-fast corner entry is the #1 reason for single-vehicle motorcycle crashes.

Josh and I had worked together during a Personal Instruction Day last week at the NH track on strengthening his “skill foundation” to allow him to safely “drive” his bike at the pace he is eager to achieve.
We made good progress, but the eagerness and drive Josh has for rapid improvement seems to cause him to push harder than he should. This is common with highly motivated people. I can name two other very good riders who are motivated to ride at a top level, but have not yet learned and applied all the information necessary to be able to ride at that level…yet.

All motorcyclists who are eagerly developing their physical skills must also develop their ability to monitor their attitude, self-evaluate their real progress, and use judgement that is in line with their true capabilities.

The Physical Solution

Now that we understand that the crash could have been avoided with a bit of “judgment double-check”, let’s talk about what went wrong and the mechanics of how the crash could have been avoided. Remember: A too-fast corner entry is the #1 reason for single-vehicle motorcycle crashes.

Because Josh had decided to “let it rip” down the straight (probably faster than he had done before), he entered the turn 1 braking zone at a higher speed than he had previously. That’s fine, BUT he did not adjust his braking behavior to match the increased approach speed. With an increase in speed comes the need to:

brake earlier using the same or similar amount of brake force as when approaching at a slower speed, or
use the same brake marker as when approaching the turn at the slower speed, but brake harder, or
a combination of #1 and #2

Either method will work to achieve the goal of slowing to a comfortable entry speed. Braking earlier is generally the best solution where you have more time and space to modulate your brake force to slow without anxiety.

Josh did not alter his “begin braking” mark, so he found himself flying past his usual brake marker and therefore reached his turn-in point at a higher speed than he was familiar (or comfortable). You can clearly see in the forward-facing camera angle that he was missing the apex and then used greater handlebar pressure (countersteering) as he attempted to stay on the track, which overtaxed the front tire and it tucked.

An Expert’s Solution

Could the crash have been avoided in the hands of a seasoned expert? With the bike at that speed and in that position in the corner, I would say maybe, but probably not. HOWEVER, the expert would have identified that he or she was traveling faster than before and because of this, would have adjusted the “begin braking” location to be earlier and increased the amount of brake force as needed to slow down sufficiently. Expert-level track day riders are comfortable braking very hard, because they have practiced this skill.
He or she would have also used trailbraking to further scrub off speed if necessary as the bike was eased into the corner. However, I want to emphasize that trailbraking is not really “meant” to be a technique used to salvage a blown corner. Done correctly, trailbraking is a planned method for stabilizing the motorcycle when entering corners. That said, if you have trained yourself to trailbrake as it is meant to be used, then it is at your disposal when you need a longer duration of braking force if you inadvertently enter a turn too fast. Read all about trailbraking HERE.

The Lesson

Remember that if you change one thing (faster straightaway speed), you must adjust other things (brake marker and/or brake pressure) to reach the entry speed you are able to handle. Please learn from Josh’s unfortunate mistake and keep your enthusiasm and eagerness in check and resist introducing significantly faster speeds until you understand the concept of cause and effect as it pertains to adjusting entry speed.

Crash Videos

Front view:

Rider Face View:

A message from Josh himself about what he learned:

Staying within limits is a lesson I strive to drive home to my students every weekend as an MSF RiderCoach. The motorcycle, the rider, and the time & space limits around them. My hope is that every rider I come in contact with has takeaway points and thinks about actions and decisions made while riding.
My overall goal as a rider is to learn, fine-tune, and practice as many new and advanced skills as I can. I feel the biggest joy of riding is that there is always something new to work on or perfect. Each year I try and take on something new I can use as a rider and coach. A few years ago I had an opportunity to take a course on dirt bike techniques and later on I was able to become a certified MSF Dirt bike Coach. Last year my new goal was to learn to become proficient in riding on the racetrack at speed.
I went out and bought every book and DVD I could find on the subject, and also a shiny GSXR 1000 that I thought at the time would be a perfect bike to go out and lay down some hot laps. Books and video’s are great tools, however to really be able to learn and apply the skills takes tons of coaching, practice and fine tuning.
My biggest obstacle is always trying to rush and accelerate my learning. I want so bad to be the best and smoothest that I do not take the advice I give to my students. I try and go from step A all the way to step Z in one day. Learning should be in stages and is a building block process. Learn the gross skill 1st and stay within your limits. Ken gave me the best advice of all when he said “Slow down and get smooth 1st”.
I was doing pretty good and learning the New Track. Taking my time and finding reference points and determining where I should look, brake, tip, and accelerate. It was near the end of the day with only 2 sessions left. I was a little tired and sore from working hard on my body position and riding. I started the 2nd to last session and started letting my mind drift away a little bit. I was thinking about the ride home and my fatigue level and on the video footage I had been recording all day; what I would be showing my friends and family and how cool I would look.
I decided to try one more lap and call it a day. I said to myself. “You can push a little harder and get one awesome lap to end the day.” I got to the start of the straight. I did a head check to see if I was holding up any riders. The coast was clear and I gave it all I got. I pinned the gas and tucked my head. Glancing at the speedometer I saw the numbers climbing 130,140,150. I looked up and saw the end of the straight fast approaching. I got on the brakes with a force that seemed very heavy. I was squeezing in on the tank with all my might to hold myself from pushing forward. I saw the turning point approaching fast and thought “Oh No I just blew it” I had lots of speed and not much track left.
I thought in the back of my head. You can do this, usually riders have less skills than the machine they are on. I tried as hard as I could to get into a hang off position and turn the bike. I gave it a flick into the corner and felt the front dropping out. I saw the ground rushing up to my shoulder and I lifted my head up and away from the turn. Boom, I was on the ground and tumbling, I could see the bike flipping as I was tumbling and sliding into the grass. Every second was in slow motion as I could hear the plastic cracking and breaking off the bike.
It seemed like I was going to slide forever and I was saying to myself. OK, please stop now. Once stopped I stayed still, counted to 10 and started to assess if anything was hurt or broken. Not even a scratch. All the gear I had invested in paid off big-time! I looked at the bike and wanted to cry. I knew as I started to scream down the straight I was pushing too hard. I had not taken the advice I want to instill in every single student. I got up and started looking the bike over. Seeing everything all smashed is a feeling I could do without. The session still had 15 minuets to go and all I could do was stand there and wave as my friends and fellow riders went by making smooth turns and having a blast. Sometimes we do not take our own advice and need a hard lesson to set us straight.
Josh

Please Donate to Keep the Articles Coming

If you liked this article and the many other articles on this site, please toss a buck or five into the hat. It’s greatly appreciated!

- Click the PayPal “Pay Now” button.
- Then indicate quantity in $2.00 increments. – Example: put “2” in “QUANTITY” field to donate $4.00, “3” for a $6.00 donation, etc.

Why $2.00? Due to the PayPal fee structure, a $2.00 donation is significantly more beneficial compared to a $1.00 donation.

Thank You!

Add your comments, below.

Stay Informed: Subscribe NOW!

Be a Better Rider: Sign Up for Personal Training with Ken

Support Riding in the Zone: Buy a book

Support Riding in the Zone: Buy products from Twisted Throttle & Amazon

May 5, 2014

Countersteering Will Save Your Life!

Getting a big (or small) motorcycle to turn requires more than just body weight.

It’s hard to imagine that so many so called “experienced” riders either fail to understand the importance of countersteering or fail to recognize that countersteering is how motorcycle really turns.

Let’s Get This Straight

A motorcycle turns by leaning. Once the bike is banked over, the geometry of the chassis, as well as the rounded profile of the tires and hard-to-describe forces cause the machine to arc around the curve. So, to turn a bike you must get the motorcycle to go from upright to leaned…precisely and efficiently.

I Don’t Need No Stinking Countersteering

A lot of riders believe that they are able to maneuver their motorcycle by simply leaning their body or by looking into the turn. While these are helpful techniques for assisting the bike to turn, they alone cannot effectively cause a 500+ pound machine to change direction.
“Yeah, but I can turn my bike without countersteering.” Um, not really. Sure, you can cause the bike to drift into a turn, but that’s not what can be called “turning”. Also, consider that most people who don’t think they are countersteering really are, they just don’t know it. Pay close attention the next time you are making any sort of turn and notice how you put a slight amount of pressure on the inside handlebar.

What Really Happens

In case you don’t already know, THE most effective way to get a motorcycle to go from upright to leaned is to introduce handlebar inputs. By pressing forward (and to a lesser degree, down) on the handlebar on the side that you want to turn, you essentially unbalance the bike so that it “falls” into a lean. Press on the right handlebar to initiate a lean to the right and press on the left handlebar to turn left. Got it?
You can enhance this effect by also simultaneously pulling on the other handlebar. This is how racers achieve quick changes in direction in chicanes on the racetrack.
Once the bike is leaned, then the front tire will steer slightly into the direction of the turn. You must relax your arms to let this natural balancing effect occur otherwise it will feel as if the motorcycle is not able to maintain the cornering path. Press, and then relax.

Why You NEED to Know How to Countersteer

Countersteering is used whenever you need to change direction. This applies to basic cornering maneuvers, as well as evasive maneuvers, such as swerving. It’s also important to be able to countersteer with authority when a corner suddenly tightens more than you expected, or when you approach a tight corner at a too-fast speed.
Not being able to get your motorcycle turned quickly will eventually result in an off-road excursion or collision with an oncoming car or a guardrail. Seriously!

Prove It To Yourself

If this makes no sense to you, then it’s time to practice. Take a look at the video clip below from the RITZ DVD for more information on countersteering and to see some drills that will help you master countersteering.

Read this article that Ken wrote for Motorcyclist Magazine about countersteering.

Listen to the Countersteering PODCAST
Add to the list in the comment section below.

Please Donate to Keep the Articles Coming

If you liked this article and the many other articles on this site, please toss a buck or five into the hat. It’s greatly appreciated!

- Click the PayPal “Pay Now” button.
- Then indicate quantity in $2.00 increments. – Example: put “2” in “QUANTITY” field to donate $4.00, “3” for a $6.00 donation, etc.

Why $2.00? Due to the PayPal fee structure, a $2.00 donation is significantly more beneficial compared to a $1.00 donation.

Thank You!

Buy Ken’s new book, “Motorcycling the Right Way”.

Read about strategies and techniques that increase safety, confidence and enjoyment.

Click Here for details.

April 24, 2014

Top 5 Ways That Motorcycle Riders Screw Up

Being average isn't good enough. — Being average isn’t good enough.

1.Thinking You Are Better Than You Are

Overconfidence and an inaccurate, overinflated self-image is responsible for a lot of motorcycle crashes. This is certainly true with young men (the majority of crashes in MA involve young sportbike riders). But, you old guys (and gals) aren’t immune. So, listen up.
Most motorcycle riders are average, at best. On the surface, they look competent enough, but when the going gets rough, their weaknesses become apparent. Everyone should occasionally look in the mirror to try and identify their weaknesses and then act to turn those weaknesses into strengths.

Group riding can bring out the worst behavior.

2. Succumbing to Pack Mentality

Group Riding can make the most level-headed rider do really stupid things. It’s something about the energy of a group, in combination with the need to prove that you’re a good rider that often fuels bad behavior. I’m not immune. Knowing that I can get sucked into riding too fast (for the street environment) causes me to be very selective about who I ride with.

3. Speeding in All the Wrong Places

Riding too fast for the street environment is one of the stupidest things you can do on a motorcycle. Yes, it sucks to get pulled over, but it sucks more to crash because you simply didn’t respect the reality of street riding. Errant cars, animals and pedestrians can jump out from anywhere and sand, gravel and fallen branches often lurk around corners undetected. I like riding fast, but not too fast. I reserve the really fast stuff for the racetrack.

4. Mixing Alcohol with Riding

Are you kidding me? As if being an average rider isn’t dangerous enough, are you willing to add impairment to the equation? Talk about stacking the deck against you. Listen, I like drinking a beer or two just like the next guy (or gal), and there was a time long ago when I would even jump on the bike after having a few. Thankfully, I survived those days.
You may think you’re fine to ride with one or two cold ones having passed your gullet, but combining drinking or other impairments with riding is totally counter to managing risk. I’m not your father, so do what you want. But, I ask you to please refrain.

5. Failing to Predict Danger

Close calls are a warning. Crashes are the result of you not heeding those warnings. The best riders develop a sixth sense about their surroundings. They scan the roadway looking for anomalies and evaluate if anything is “wrong with the picture”. They are actively searching for problems and are way ahead of the situation, because they are prepared. By “preloading” hazard scenarios into their mind, they are already halfway toward managing any hazard. Try it. Not only does it make riding safer, it’s also fun, like a video game. Don’t let them get you!
Add to the list in the comment section, below.

Please Donate to Keep the Articles Coming

If you liked this article and the many other articles on this site, please toss a buck or five into the hat. It’s greatly appreciated!

- Click the PayPal “Pay Now” button.
- Then indicate quantity in $2.00 increments. – Example: put “2” in “QUANTITY” field to donate $4.00, “3” for a $6.00 donation, etc.

Why $2.00? Due to the PayPal fee structure, a $2.00 donation is significantly more beneficial compared to a $1.00 donation.

Thank You!

Check out these related posts:

Stay Informed: Subscribe NOW!

Be a Better Rider: Sign Up for Personal Training with Ken

Support Riding in the Zone: Buy a book

Support Riding in the Zone: Buy recommended products from Twisted Throttle & Amazon

March 19, 2014

Valuing Motorcycling Skill Development

Tell this guy that learning ain't fun. — Tell this guy that learning ain’t fun.

As a motorcycle skills and safety professional, I am often frustrated and even saddened by the seemingly complacent attitude toward real skill development. It pains me to see riders who ignore the importance and benefit of learning to ride their motorcycle with more skill. Not only do sharp, well-developed skills make motorcycle riding safer, it also makes riding more engaging and way more fun.

Shut Up and Ride

I get that motorcyclists don’t ride to be safe. We ride to have fun, which means that focusing on “learning” can risk turning an enjoyable pastime into something that starts to feel like work. I’ve seen many, many motorcycle riders run away when I mention “Training” or the dreaded “S” word…Dare I say it…SAFETY.
“I just want to enjoy the wind in my face and the feeling of freedom, dude. Besides, I ride just fine.” Maybe, but could it be that riding can be MORE FUN if you learn how to ride better? Hmmmm?

Skill development benefits all types of riders.

Don’t Kill My Buzz With the Truth, Man

The repulsion toward safety and skills development is one reason why it’s nearly impossible to get experienced riders to attend an advanced riding course. The other reason is that most riders don’t see the value in developing their skill. And it’s certainly not as fun as simply going for a ride. Why “waste” a Saturday or Sunday riding around a parking lot when there are open roads to explore…and for some people, bars to hop. Did I say that out loud?
I was at a motorcycle expo earlier this year, helping to man a booth for the Massachusetts Rider Education Program (MREP). They had a riding simulator set up for people to try their hand at dealing with challenging riding situations.

Jeannine on the Smart Trainer simulator.

One guy (and I’m sure he wasn’t the only one) exclaimed proudly that he didn’t need to use the simulator because he’d been riding for 30 years. OK, said my colleague, show us what you know. The look on his face showed sudden anxiety. He kinda laughed as though we couldn’t be serious and then walked away. He was clearly afraid that he might be exposed as a mediocre rider.
This happens all the time. New track day riders are afraid that they won’t be as fast as they think they are (they’re not), and this scares them. Egos are sensitive, I get it. But, if they can man up (sorry ladies) and take the plunge, they soon discover that it doesn’t matter how fast they are, rather it’s how skilled they are at controlling their bike that counts.

What’s My Point?

You probably aren’t as good at riding a motorcycle as you think you are. “So what”, you say? Well, the last time I looked, riding a motorcycle is dangerous, even deadly. If that’s not enough to motivate you to spend a bit of cash and an afternoon brushing up on your skills, then maybe the fact that better skills means more fun will motivate you.
The vast majority of people I’ve trained over the last 20 years experience MORE ENJOYMENT after a training session. That’s because they are now more confident in their ability to manage their bike, corners and traffic. Seriously. It’s worth the effort.

Training Opportunities that are Fun

Track Days are fun and increase cornering and braking confidence.

I can’t say that the MSF courses offered around the country are exactly fun. You ride around a parking lot at 25mph as you go through specific drills that are designed to efficiently deliver vital information. Although there is a lot of laughing when groups of friends attend these parking lot courses, it’s usually all business.
When it comes to combining “fun” and “training” together, there are two venues to consider. A track day and on-street training tours.
Sport bike riders are the likely people to take advantage of track day training, but some organizations cater to all types of bikes and riders. Tony’s Track Days regularly sees sport tourers and adventure bikes at their days. But, to encourage cruiser riders and tourers to attend, Tony is offering a “non-sport bike” track day for 2014. Now, even cruiser-types can ride around a curvy ribbon of pavement without the risk of hitting a car or sliding on sand, or getting a speeding ticket.
Another fun training opportunity is on-street training tours. Stayin’ Safe has been providing training tours and I am offering tours as well. This combines scenic rides with experienced people who can offer tips for learning how to be safer and in more control.

Start the Season with Training

The snow is finally melting and now is the time to plan your season. Do yourself and your loved ones a favor and get your skills sharpened. You won’t regret it.
Share your thoughts below on your most valuable training experience.
Subscribe to the mailing list!
Buy the Book!

Please Donate to Keep the Articles Coming

If you liked this article and the many other articles on this site, please toss a buck or five into the hat. It’s greatly appreciated!

- Click the PayPal “Pay Now” button.
- Then indicate quantity in $2.00 increments. – Example: put “2” in “QUANTITY” field to donate $4.00, “3” for a $6.00 donation, etc.

Why $2.00? Due to the PayPal fee structure, a $2.00 donation is significantly more beneficial compared to a $1.00 donation.

Thank You!