Posted on

How to Survive Hairpin Turns

Practice tight turns in a parking lot.
Practice tight turns in a parking lot.

The biggest problem riders have when dealing with hairpin turns is their anxiety about being able to make the turn. It’s a good idea to practice tight turns in a parking lot before you encounter challenging hairpin turns. Read more about slow speed riding techniques.

Slow Approach

One of the most likely reasons for a crash in a corner is entering too fast. When dealing with downhill hairpin turns, you also have the additional force of gravity pushing you downhill.
The trick is to get your bike slowed early and smoothly and then carry a bit of brake force past turn in to keep the bike stable, Read about trailbraking for more detail. Just be sure the surface is clean enough to allow slight braking while cornering.

Throttle On

When making slow turns, it is important that you maintain slight, steady forward drive for stability. If you chop off the throttle, you’ll probably fall.
A bit of forward drive takes some of the load off the front tire when going downhill and gives you forward momentum when going up a hill. It also maximizes ground clearance.
But, be careful. If you are abrupt with the throttle, either by accelerating too hard or by chopping off the throttle, you risk running wide, overtaxing the tires and upsetting the chassis and balance

Downhill turns are challenging enough to put a sign up.
Downhill turns are challenging enough to put a sign up.

When approaching a downhill hairpin curve you need to slow down more to manage gravity, but also to allow you to crack the throttle slightly for maximum stability. From a slow entry speed, give the bike enough throttle (as soon as you begin to lean) to maintain steady drive through the whole curve. Try not to decelerate. Be sure to look well into the turn, at the corner exit.

Uphill Hairpins

When going uphill, you can approach with a bit higher speed. But, slow down enough to allow steady throttle throughout the whole turn. Be sure not to use too much throttle that you cause the front tire to lose traction and “skate”, which can push your bike too far to the outside of the turn. You also don’t want to overload the rear tire with too much acceleration force. Steady, gradual throttle at the beginning of the turn is the key. Again, keep your eyes pointed all the way to the turn’s exit.

Look through the turn and accelerate slightly.
Look through the turn and accelerate slightly.

Enough Speed

Whether going up or down hill, you need to keep your speed above about 10 mph to maintain balance and stability. Sometimes, people simply fall over because they are going too slow. At very low speeds, slight deceleration or shift in body weight (tell passengers to remain relaxed, but still) is enough to upset balance and cause a tip over. Aim for smooth, steady drive.

Look Toward the Exit

Your eyes help direct your bike to where you are looking so look where you WANT to go. Turn your head to ratchet your eyes through to corner, always looking to the next visual target…entry, apex, exit. Read more about visual skills here.

What’s My Line?

It's important to get this right.
It’s important to get this right.

Try to select a cornering line that allows you to get your steering inputs done early and so the throttle finishes the turn. This usually means an outside-inside-outside path of travel. There are many advantages to this line, including a wide view through the turn and the ability to perform a quick turn-in that gets the bike turned early. It’s common for riders to fall in slow, tight corners because they introduce mid-corner steering inputs at the time when the front tire is already working hard.

Obligatory Crash Video

Here’s a video of my friend Matt who found out how a slight miscue in a slow, tight turn can put you on the ground. He was a rather new rider at the time and was spooked by the traffic. The bike was borrowed, so it was not familiar to him, either. He was unhurt. Erik from Twisted Throttle evaluates the crash protection from SW-MOTECH.

Why do you think Matt crashed? I’ll give my opinion in the comments below after some of you respond.
What tips do you find useful when dealing with hairpin turns?

Please Donate to Keep the Articles Coming

If you liked this article and the many other articles on this site, please toss a buck or five into the hat. It’s greatly appreciated!

    • Click the PayPal “Pay Now” button.
    • Then indicate quantity in $2.00 increments. – Example: put “2” in “QUANTITY” field to donate $4.00, “3” for a $6.00 donation, etc.

Why $2.00? Due to the PayPal fee structure, a $2.00 donation is significantly more beneficial compared to a $1.00 donation.

Thank You!




Check out these related posts:

submit to reddit

Stay Informed: Subscribe NOW!
Be a Better Rider: Sign Up for Personal Training with Ken
Support Riding in the Zone: Buy a book
Support Riding in the Zone: Buy products from Twisted Throttle & Amazon
Twisted_Affiliate-Interphone-widget
Twisted_Affiliate-Interphone-widget
Posted on

10 Ways to "Look" Like a Pro

Look where you want to go!
Linda Blair, The Exorcist?

No doubt that being able to quickly and precisely flick a motorcycle into a corner can make you a cornering hero. However, the physical act of cornering is only one aspect of cornering mastery. Safe and skillful cornering also requires that you gather information about the corner—information gathered through your eyes.
The Eyes Have It
When cornering, your eyes alert you to any obvious hazards, help you determine how tight the curve is and allow you to identify any corner characteristics that might affect your safety. But, simply looking ahead isn’t enough to get the information you need. There is a difference between “Looking” and “Seeing”. Also, how you look is critical. A lazy gaze will get you nowhere fast. Aggressively scanning and searching for specific targets is much more effective.
Linda Blair head turn.
Look well ahead.

1. Look well ahead

The first thing to do is get your eyes up! The earlier you spot a hazard or identify a corner’s characteristics, the less likely you are to act out of panic.
Looking well ahead also reduces “speed anxiety” by slowing down the landscape. A slower perceived rate of speed offers a greater feeling of control and minimizes the effects of speed-induced anxiety.
When cornering, look as far ahead as you can, all the way to the corner’s exit if possible.
How far ahead you are able to see depends largely on the environment. You can scan to the horizon in corners that are open, flat and unobstructed. However, in forested or hilly locations you will encounter many blind corners that provide little sight distance. This lack of visual lead time can make it difficult to see unexpected roadway hazards until it is too late.

2. Match Your Speed to Your Visual Distance

Ride at a speed that matches the amount of visual lead time you have. If you are riding too fast to process the information, you will be behind the eight ball and not have enough time to react.
There are often roadside objects that hide critical information. Always enter turns at a speed that takes into account the lack of visual information and allows you ample time and space to avoid whatever might be around the bend.

3. Identify the Right Entry Speed

Skillful cornering requires accurate visual information about a corner’s radius, camber and surface quality so you can determine the right entry speed.
A too-fast entry speed is responsible for the majority of single-vehicle crashes as the panicked rider target fixates and runs off the road or grabs the brakes and crashes. Use visual information to determine whether your pace is within your comfort zone.

There's a lot to look for on the street.
There’s a lot to look for on the street.

4. Identify visual clues

By looking well ahead you can evaluate a corner’s unique characteristics and come up with a cornering plan. Certain roadside features can help you identify a corner’s character and allow you to establish a plan to help you decide what line you’re going to take and where you’re going to get on the gas.
One useful visual target that helps you make this plan is the “vanishing point” where the white painted fog lines or painted centerline visually converge.
On the track, there are no lines, so use the edges of the pavement. How soon the lines or pavement edges converge in the distance help to determine how tight a corner is and which way the surface slopes.
If the lines or pavement edges converge in the near distance, then you can count on a tightening corner radius. On the other hand, a distant vanishing point indicates a larger radius or a curve that is ending.
This information can also help you determine road camber or slope. When a road is positively banked, the road edges do not come together right away.

Look where you want to go.
Look where you want to go.

5. Look in the direction you want to go

Looking where you want to go can help direct your motorcycle through the turn. This is commonly known as “visual direction control”. Visual direction control is essentially your eyes telling your mind where you want the motorcycle to go next.
When cornering, point your eyes to the corner’s exit to help direct your motorcycle on the desired path. Riders who discover the benefits of looking well ahead when cornering often comment on how much easier their motorcycle seems to turn.

6. Keep your vision wide and your eyes moving

Your eyes must move quickly between the corner locations while at the same time scanning for surface hazards. Keep the majority of your vision well ahead into the corner, however you may need to look down briefly to monitor the surface condition as it nears. Do this by using quick downward glances.
Continually gather information from near and far with upward and downward, and side-to-side search pattern. Scan aggressively to gather as much information as you can about the road surface and corner characteristics. Finally, look through the turn to the exit and identify what is in store farther up the road.

Always be looking for reference points when riding on the track.
Always be looking for reference points when riding on the track.

7. Look for Reference Points

Reference points help you place your tires exactly where you need them to be. Reference points are somewhat less helpful or necessary on the street, because speeds are low where precision is less critical.
But on the racetrack where you visit each corner many times a day and where the speeds are much greater, reference points are critical and a relatively small miscue  can result in an off-track excursion.
Once you establish the best cornering line, you can then use reference points to make sure you are always on that line lap after lap. Cones, pavement stains and cracks, as well as distant visual targets (trees) can all be effective reference points.

8. “Ratchet” Your Eyes

To make visual direction control work for you, look into the curve and then continue to move your vision along the desired cornering path all the way to the corner exit as though your eyes are pulling the motorcycle through the turn.
Your eyes cannot help but stop to focus on small targets as you scan ahead. Look around the room, trying to not have your eyes “flick” slightly as you scan. You can’t. So let this natural occurrence work for you.
Imagine your eyes moving through a corner in a sort of ratcheting way, very briefly noticing visual targets and reference points along the way. Put all these “dots” together to make a smooth corner.

9. Look at the solution, not at the problem

Visual direction control can work for or against you. It can work against you if your eyes fix on a hazard that you need to avoid, which is what we tend to do under threatening situations. “Target Fixation” is the term used to describe this response. The problem is that if you look at a hazard, such as a patch of sand or the edge of the road, you will likely end up riding directly toward it.
If a panicked rider were able to keep his vision and attention focused on the corner’s exit he will have a fighting chance of making it. I’ve seen time and again riders who give up on making a corner even when the bike is capable of leaning further and completing the turn. Focus on the solution, not the problem!
The same goes with passing on the racetrack. If you fixate on the tail of the rider ahead you will have a harder time getting by. But, if you look past the slower bike and trust your peripheral vision to monitor the slower bike, then you can dispatch the backmarker much more easily.

10. Practice Your Visual Skills

Avoiding target fixation is easier said than done, because we are naturally wired to closely monitor threats with our eyes. It is therefore important to train yourself not to do what comes naturally and instead look away from a threat.
On your next ride, consciously look away from road surface obstacles, such as a manhole cover, pothole or road kill and look toward an escape route. Continue to increase awareness of this problem and practice to make the solution second nature.
When it comes to cornering, consciously look farther ahead. And don’t just look, but see the information that is most meaningful.
On the track, look farther ahead. If an obstacle, such as airfence, or a cresting hill blocks your view, look “through” it so your eyes are where you need them to be in the next second when the obstacle is no longer in the way.
What visual techniques have you discovered that help you?

Please Donate to Keep the Articles Coming

If you liked this article and the many other articles on this site, please toss a buck or five into the hat. It’s greatly appreciated!

    • Click the PayPal “Pay Now” button.
    • Then indicate quantity in $2.00 increments. – Example: put “2” in “QUANTITY” field to donate $4.00, “3” for a $6.00 donation, etc.

Why $2.00? Due to the PayPal fee structure, a $2.00 donation is significantly more beneficial compared to a $1.00 donation.

Thank You!




Check out these posts:

How Can I help You? Online Coaching NOW AVAILABLE
Stay Informed: Subscribe NOW!
Trianing-Tours_LandingBe a Better Rider: Sign Up for Personal Training with Ken
Support Riding in the Zone: Buy a book
Support Riding in the Zone: Buy products from Twisted Throttle & Amazon
Twisted_Affiliate-Interphone-widget
Twisted_Affiliate-Interphone-widget

 

Posted on

Is Crashing Really that Bad?

This crash could have been deadly, but thankfully not.
This crash could have been deadly, but thankfully not.

Crashing a motorcycle sucks. No doubt about that. I’ve had my share of run-ins with gravity and it’s not fun. But, does crashing a motorcycle always mean carnage and a hospital visit? It depends.

My crashes

I’ve had only one “real” street crash and one minor one. The minor one involved a car who rolled into the back of my Triumph Bonneville. I didn’t fall, so it was very minor.  I also had a minor parking lot tipover (note to self: remove the disc lock before attempting to ride away). But tipovers aren’t exactly what I call “crashes”.
The “real” crash happened in 1978 when a car driver turned left in front of me…classic.
Thankfully, most of my crashes were racing incidents. I say “thankfully” because even though racing crashes suck, they don’t suck nearly as much as street crashes where the chances of injury after sliding into a tree, guardrail or oncoming car is quite high.
I’m truly grateful that the extent of my injuries from both track and street crashes were cracked ribs and a broken foot from the tipover.  These injuries were painful, but all healed without any complications.
Unfortunately, the “real” street crash resulted in a totaled 1973 Yamaha TX650 and the rear-end incident resulted in the Triumph’s taillight being smashed, but that’s what happens when you make impact with cars.
In all of the track crashes, bike damage was limited to easily replaceable parts, allowing me to get back on the track later that day. Sure, the cosmetic damage was a bummer, but I got over it–most people do.

Too much throttle, too quickly. photo by Tim Richer
Too much throttle, too quickly. photo by Tim Richer

Safer Crashing

There was a time when crashing on the racetrack was just as likely to get you killed as crashing on the street. This was because racetrack safety was abysmal with concrete walls lining the course and pavement not any better than a potholed rural road.
Thankfully, track safety is much improved. Even though a lot of people complain about the safety issues at my local track (Loudon, NH), the current track is much better than the old Bryar track that had all sorts of safety problems. We didn’t complain much, since all of the tracks were that way.
Another reason there are fewer deaths and injuries today is because of better protective gear. Pudding bowl helmets lined in cork were the racers’ choice at one time. Now, we have helmets that are pretty darn effective at preventing the majority of head injuries. Add to that the improvements in material and armor incorporated into jackets, pants, boots and gloves and it is possible to crash without suffering too badly.
Of course, where you crash is the biggest factor in whether you will end up in a hospital or hearse. Collide with a car and even the best riding gear is not likely to save you from some kind of injury. Crash on a modern racetrack, and you’ll likely get up, brush yourself off and walk back to the pits under your own power.
Unfortunately, road safety has not improved for motorcycle riders. More tar snakes and guardrails seem to appear every year and drivers are more and more careless about paying attention. And road conditions are often allowed to get pretty bad before they are fixed.

Crashing on the street is a
Crashing on the street usually results in injury.

Perception of Risk

It’s been proven that people take greater risks when they feel protected. This is why drivers of large SUVs tend to feel less threatened than drivers of small cars. Most motorcycle riders understand that they are vulnerable to injury and ride accordingly.
This is why Risk Ignorance and complacency is so dangerous. The risks don’t change, but the inaccurate perception of the danger can make a rider think he or she can ride more aggressively or with less attentiveness.
Believe it or not, there were fewer racing crashes back in the day when races were held on road courses lined with stone walls, hedgerows, fences and houses lining the circuit. Racers knew that a fall would very likely result in death. So, most rode in a way that balanced risk and reward.
Today, there are many more crashes, but many fewer deaths and serious injuries because, with the exception of the Isle of Man and a few other “real” roadrace circuits, racing is conducted on closed courses with safety features such as runoff, gravel traps and airfence. Also, today’s protective gear is so much better. This means that racers can push harder, knowing that a crash will probably not be the end of the world.
Now, don’t get me wrong, racetrack crashes can be lethal. It’s just that the risk to reward ratio has shifted so that it’s not unreasonable to expect to get up unscathed after a racetrack crash.

The Perception of Crashing

Another advantage racers have when it comes to crashing is that racers expect to crash. After all, they are pushing the limits of grip and skill and are sharing the track with a bunch of crazies all set on going as fast as they can, determined to take your spot on the podium.
So, when you do crash in a race situation, it’s not unexpected. And if you do go down, it’s unlikely that you are seriously injured, so you get over it rather quickly. This makes the mishap psychologically easier to deal with.
It’s different when you don’t expect to crash. For instance, crashing during a track day will likely be more upsetting, because it is not assumed that crashes are inevitable. But, track day crashes still fall under the category of “not likely to get injured”, so most track day crashers get over the mishap fairly easily.
Crashing on the street is a whole other matter. Street crashes are often particularly traumatic, not only physically, but also mentally. Most street riders assume that they will not crash, even though the risks are actually much greater when riding on the street. It’s understandable, because most street riders go many miles and years without a crash, which makes it easy to think that it won’t happen to them. So when it does, their world is shattered, even if they don’t suffer a significant injury.

Jeannine knows the importance of practice and risk management.
Jeannine knows the importance of practice and risk management.

Thankful, But Skillful

I’m able to write about my crashes today, because most happened on the racetrack in a controlled environment. I’m thankful that I have experienced very few street crashes.
Perhaps some of the reason why I’m still in one piece is luck, but I contend that the reason I have had few street crashes is because of my commitment to riding smart and never becoming complacent about risk. This includes learning all I can about riding and implementing effective strategies when riding in traffic or in the twisties.
Risk is always there and always will be. Learn to manage risk and perhaps you can join me as one who is mostly unscathed after many decades of riding a motorcycle…if we stay sharp and are blessed with a bit of luck.
What have you learned from your crashes?

Please Donate to Keep the Articles Coming

If you liked this article and the many other articles on this site, please toss a buck or five into the hat. It’s greatly appreciated!

    • Click the PayPal “Pay Now” button.
    • Then indicate quantity in $2.00 increments. – Example: put “2” in “QUANTITY” field to donate $4.00, “3” for a $6.00 donation, etc.

Why $2.00? Due to the PayPal fee structure, a $2.00 donation is significantly more beneficial compared to a $1.00 donation.

Thank You!




Check out these posts:

How Can I help You? Online Coaching NOW AVAILABLE
Stay Informed: Subscribe NOW!
Trianing-Tours_LandingBe a Better Rider: Sign Up for Personal Training with Ken
Support Riding in the Zone: Buy a book
Support Riding in the Zone: Buy products from Twisted Throttle & Amazon
Twisted_Affiliate-Interphone-widget
Twisted_Affiliate-Interphone-widget

 

Posted on

5 Bad Habits You Must Fix, NOW!

Crash-SignNo matter how “good” a rider you are, it’s likely that you have at least a few bad habits and attitudes. Poor habits and dangerous perceptions can develop over time without us even knowing it. That is, until we experience a close call or crash. Let’s take a look at a few bad habits that many riders possess.

1. Believing You’re a Better Rider than you Are

A lot of RITZ blog readers would be considered “experienced” riders. But, the truth is that experience alone does not make you a proficient rider. I can’t begin to count how many so-called experienced riders I’ve encountered who demonstrate a significant lack of proficiency. Unfortunately, unless the rider admits that he or she has a problem and asks for advice, their poor riding will continue indefinitely and ultimately lead to a mishap.
Unsolicited advice usually is not appreciated, so knowledgeable riders are reluctant to share their wisdom to the riders who need it most. Attempts to enlighten the problem rider often results in exclamations about how many years of riding experience they have and that they know all they need to know to get by…never really knowing the danger they are in.
The solution? First, take a good look in the mirror. What skills are you lacking? (I’m sure there are many, but let’s stick with motorcycle-related skills for now). Next, get the knowledge and training you need to bring all of your skills up to snuff. Thirdly, remind yourself that what skills you have are perishable and need to be kept fresh.
Promise yourself that you will purposefully practice braking, turning, and swerving. It doesn’t have to take a lot of effort to keep skills sharp. Learn about proper cornering technique and then practice it on your Sunday rides. And be sure to learn about all the ways to keep yourself safe in traffic and practice on your way to work every day. Over time, you just might become as good as you think you are.

Always remember that you are vulnerable...and hard to see.
Always remember that you are vulnerable…and hard to see.

2. Forgetting You Are Vulnerable

Experience can often lead to complacency. If you ride many miles without an incident, you are at risk of thinking that riding a motorcycle is not as dangerous as it’s made out to be. This perception leads to many crashes and fatalities. Complacency and overconfidence can occur when you don’t recognize subtle signals that indicate just how close you are to catastrophe.
Get into the habit of recognizing clues that should alert you to threats. Make a concerted effort to scan the landscape and roadway for anything that can turn into a hazard, such as a reflection on the windshield of a car that is rolling toward you. Ask yourself whether the driver sees you and what are the chances that he will accelerate in front of you.
Evaluate each clue to determine whether you can reliably read what is being communicated. For instance, direct eye contact with the driver may indicate that the he sees you, but don’t count on it!

What's around that corner?
What’s around that corner?

3. Assuming the Coast is Clear

You know what they say about making assumptions, right? “They make an ASS out of U and ME”.
One of the most problematic situations is when a motorcycle is approaching an intersection with other drivers waiting to turn left across the rider’s lane. Part of the problem is that the approach speed of a narrow vehicle is much harder to judge compared to a wide vehicle. This is why motorcyclists experience drivers “cutting them off”.
The drivers aren’t necessarily out to get you; they more likely misjudged your approach speed and thought that they had plenty of time to make the turn. The message is to never assume that a driver who appears to see you will not cut in front of you. See “The Top 2 Survival Tips That Will Save Your Life” for more on this topic.
A lot of riders also assume the coast is clear around corners. Depending on the region you ride in, many, or even most corners you encounter do not provide a clear view of the corner exit. Hillsides, vegetation and roadside structures all conspire to block your vision.
Too many riders approach corners at a speed that does not allow the time and space to stop or maneuver if a mid-corner hazard were present. It’s a good idea to enter blind turns slow enough so you can confidently avoid a hidden hazard. If no hazard exists, then you can roll on the throttle and accelerate safely though the turn with no drama.

Caroline
Caroline wears ATGATT

No Gear=Greater Risk of injury
No Gear=Greater Risk of injury

4. Not Wearing ATGATT

ATGATT is an acronym that stands for “All The Gear, All The Time”.  MY definition of “All the gear” means helmet, appropriate eye protection, jacket and pants with protective armor, gloves, and over-the-ankle boots. The obvious reason for buying and wearing all this gear is for protection in the event of a crash. Since motorcycle riders don’t have bumpers, airbags, crumple zones and safety glass surrounding us, we must wear our protection.
Unfortunately, way too many motorcyclists choose not to wear full protective gear. In states where helmet laws are enforced, riders are compelled to wear this most important piece of protective gear, but helmet choice states leave the option of helmet use to the rider. Whether you agree with helmet laws or not, it’s hard to dispute the benefits of having a helmet strapped to your head when you and your bike separate at speed.
Currently, no states require any other protective gear to be worn, with the exception of eye protection. This means that you can ride legally in a tank top, shorts and sandals. Good luck with that.
The reasons why riders do not wear protective gear often include image, peer pressure (you gotta look cool), and cost. But, there is plenty of inexpensive protective gear that meet most rider’s fashion sensibilities while providing decent protection (at least for a single crash).

Both speed and lack of visibility caused this crash.
Both speed and lack of visibility caused this crash.

5. Being an Idiot

This topic can cover a lot of ground, but let’s focus on your attitude when you ride. This pretty much means riding with your head securely screwed onto your neck. Letting destructive influences like ego, peer pressure, intoxication, and distraction make decisions for you will eventually lead to a hospital visit. So, just say no to stupidity. ’nuff said.
What would you add to this list of bad habits?
submit to reddit

Please Donate to Keep the Articles Coming

If you liked this article and the many other articles on this site, please toss a buck or five into the hat. It’s greatly appreciated!

    • Click the PayPal “Pay Now” button.
    • Then indicate quantity in $2.00 increments. – Example: put “2” in “QUANTITY” field to donate $4.00, “3” for a $6.00 donation, etc.

Why $2.00? Due to the PayPal fee structure, a $2.00 donation is significantly more beneficial compared to a $1.00 donation.

Thank You!




Check out these posts:

How Can I help You? Online Coaching NOW AVAILABLE
Stay Informed: Subscribe NOW!
Trianing-Tours_LandingBe a Better Rider: Sign Up for Personal Training with Ken
Support Riding in the Zone: Buy a book
Support Riding in the Zone: Buy products from Twisted Throttle & Amazon
Twisted_Affiliate-Interphone-widget
Twisted_Affiliate-Interphone-widget
Posted on

The Key to Motorcycle Safety (and Fun)

What kind of attitude about safety does this suggest?
What kind of attitude about safety does this suggest?

It’s probably not what you think.
You wouldn’t be alone if you thought that the most important part of riding a motorcycle is to learn the physical skills, such as braking, cornering, slow speed maneuvers, and perhaps swerving. While those are very important skills to master, it is the mental skills that are the most critical skills to develop when it comes to reducing injuries and death. And the most important mental skill of all is attitude.

Wait, what?

Yes, in my opinion attitude is the most critical thing to get right; before cornering, or braking, or strategies for managing traffic. Attitude colors the relationship a rider has with motorcycling. A positive and committed attitude toward safety needs to be established from the start and maintained throughout a rider’s two-wheeled career. That’s right, I said career, how’s that for a committed attitude?

Shut Up and Ride

I know that this kind of talk can be a buzz kill. I would rather ride without the need to consider the limits of the riding environment. Sometimes I just want to ride like the twisty public roads are my own personal racetrack, and there are times I just don’t want to play well with other drivers. Unfortunately, I know too many motorcycling friends who died too young to not take the limits seriously.
It’s not enough to be very skilled at controlling a motorcycle. If your attitude stinks and you can’t seem to keep a healthy balance between fun and safety, then your days on two wheels are likely numbered. So, I say Shut Up and Ride WELL!

This guy was a student of mine some years back. His attitude for learning to be the best rider he could be was contagious.
This guy was a student of mine some years back. His attitude for learning to be the best rider he could be was contagious.

The good news is that a positive, committed attitude also leads to more enjoyment and fosters the often-illusive “Zone” that most of us covet.
All photos © Ken Condon

You Have to Want It

How badly do you want to survive? Perhaps I’m being melodramatic, but it’s a serious question. When it comes to participating in a sport where people die, you owe it to your loved ones and yourself to ask that question. If the answer is “I really, really want to survive”, then do something about it.
It’s important to have excellent physical skills, such as cornering, braking and the ability to perform evasive maneuvers. However, superior mental skills prevent the vast majority of close calls and crashes. Learn to play the mental game and you’ll be a winner. Refuse to learn the tricks of motorcycle control and survival and you’ll lose.
But, it all starts with a committed attitude. Without an attitude that prioritizes risk management, then it’s unlikely that really proficient mental and physical skills will ever develop. It takes a commitment to be really good at anything, including motorcycling. Without a certain level of commitment, you can count on mediocrity. Can motorcycle riders afford to be mediocre?

Please subscribe to my Newsletter Mailing List

Please Donate to Keep the Articles Coming

If you liked this article and the many other articles on this site, please toss a buck or five into the hat. It’s greatly appreciated!

    • Click the PayPal “Pay Now” button.
    • Then indicate quantity in $2.00 increments. – Example: put “2” in “QUANTITY” field to donate $4.00, “3” for a $6.00 donation, etc.

Why $2.00? Due to the PayPal fee structure, a $2.00 donation is significantly more beneficial compared to a $1.00 donation.

Thank You!




Check out these posts:

How Can I help You? Online Coaching NOW AVAILABLE
Stay Informed: Subscribe NOW!
Trianing-Tours_LandingBe a Better Rider: Sign Up for Personal Training with Ken
Support Riding in the Zone: Buy a book
Support Riding in the Zone: Buy products from Twisted Throttle & Amazon
Twisted_Affiliate-Interphone-widget
Twisted_Affiliate-Interphone-widget

 

Posted on

The Top 2 Survival Tips That Will Save Your Life

Both speed was and lack of visibility caused this crash.
Both speed was and Lack of Visibility caused this crash.

I know what you’re saying. “You’re telling me that there are only 2 things I need to do to survive riding on the street?” You betcha. So, here is the caveat to this sensational statement; there are more like 1 Gazillion things you need to know to be the safest rider you can be. But, I don’t have that much time and you’d be bored by the time I got to number 15,000. So, I’m going with my top 2.
And with no further ado, here they are. The envelope. please.

#1 Being “Speed Smart”

#2 Being Visible

Of all the things you can and should know about riding a motorcycle, these two strategies will allow you to avoid 80 to 90% of the most common situations that lead to motorcycle crashes. I hear you yelling at your laptop or smartphone saying “What about [INSERT YOUR FAVORITE STRATEGY HERE]”. I understand… really. There is way more to know to avoid becoming roadkill than just these two strategies. But, I contend that most close calls and crashes can be avoided if you follow my suggestions and focus first on these two strategies. Let me elaborate.
All photos © Ken Condon

Top Motorcycle Survival Tip #1: Be Speed Smart

Jeannine being Speed Smart
Jeannine being Speed Smart

Being “Speed Smart” doesn’t necessarily mean sticking to the posted speed limit. I’m no angel when it comes to ignoring ridiculous speed limit signs, especially when the payoff is worth the risk of a ticket ( a great section of twisty tarmac with little traffic). No, I’m talking about being smart about when and where you wick it up. You can avoid a majority of close calls if you just keep the throttle under control. Here’s how.

Ride at “Expected” Speeds

It’s important to ride close to the marked speed limit when riding through town centers, and whenever you are near other drivers, especially when riding through intersections. Riding at a speed that is greater than is expected will likely result in the driver pulling in front of you, thinking he or she has time to go. This is largely because a motorcycle has a narrow frontal area, which makes it more difficult for drivers to judge your approach speed and distance.

Ride Slow in a Slow Environment

One of the most common reasons motorcycle riders crash is because they ride faster than the environment will safely allow. Riding at the speed limit makes total sense when there is a lot of traffic, but what about when the road opens up? It may be tempting to go WFO, but no matter how much you wish the road were a racetrack, it is not! You can get away with excessive speed for a while, but some day it will bite you. I can almost guarantee it. Really fast sport riding belongs on a racetrack, dummy.
Even if you are a racetrack hero, you must understand that the unpredictable nature of the street does not allow you to exercise your full cornering prowess. With hazards such as road surface hazards, unexpected changes in radius and camber, or other vehicles crossing into your lane you can easily exceed the limits of the environment even though you may be nowhere near your personal limits.

Cornering Correctly: Slow in, Fast out

The vast majority of single-vehicle crashes are the result of riders failing to negotiate a curve and a common reason for this is a rider entering a corner at a speed that is too fast for the conditions or for the rider’s ability. The best strategy is to slow to a conservative speed and then gradually accelerate when you are sure it is safe to do so. Keep in mind that you can always get on the gas, but you can’t go back in time to enter the turn at a slower speed.

Respect Time and Space

Still not convinced just how significant speed is to keeping you safe? Then consider the timing and circumstances of a typical 30 mph crash. At that speed you are traveling at 44 feet per second (1 mph = 1.47 ft/sec). Getting a motorcycle stopped at 30 mph takes just over two seconds and requires about 35 feet of space. But, braking distances include more than just the time and space to physically stop your motorcycle. It also includes “thinking time” and “reaction time”. At 30 mph you can count on using about .7 seconds or 31 feet to realize that there is a problem. It then takes you another .3 seconds or 13 feet to react by rolling off the throttle and reaching for the brakes. That means you traveled 44 feet before even touching the brakes. Finally, it takes you about 2.2 seconds or 35 feet (with a typical deceleration rate achieved by the average rider) to bring the motorcycle to a halt. Add this “braking time” to the “thinking time” and “reaction time” and you’ll need a total of 3.2 seconds and 79 feet with which to stop.

Top Motorcycle Survival Tip #2: Be Visible

"SMIDSY"= "Sorry Mate, I Didn't See Ya"
“SMIDSY”= “Sorry Mate, I Didn’t See Ya”

The most common phrase uttered by drivers who are involved in a motorcycle crash is; “I didn’t see him”. It’s easy to blame the driver for being inattentive. After all, texting, NAV systems, and other distractions are vying for drivers’ attention…you know who you are. While this is a reality on today’s roads, too many riders fail to recognize their role in being visible, choosing to wear dark colors and riding in a way that hides them from other drivers.
Even being seen is not as reliable as we would like. Most motorcyclists have stories of drivers pulling out in front of them even though the driver was looking directly at them. What would cause a driver to proceed if the rider was in plain sight? It’s common for a driver’s brain to dismiss the appearance of a relatively insignificant (small) vehicle (motorcycle) on the roadway and pull out without ever “seeing” the motorbike.

Use Effective Lane Positioning

In traffic, it’s important to constantly evaluate your ability to see and for others to see you. Poor lane position is a factor that can prevent you from being seen and seeing hazards. This includes not having sufficient following distance. Ample following distance provides a wider angle of view to see past the vehicle and allow other drivers to see you.
Proper lane positioning also includes your location within the width of your lane. Motorcycle riders have the option of riding in the left, center or right portion of the lane. This gives you the ability to place your bike where you can see farther ahead and where other drivers can see you. Exactly what is the best lane position? In many situations, riding in the left/center of your lane makes the most sense. This position allows you to see past the vehicle ahead and gives you a good angle of view of the oncoming lane.  Certain situations require you to alter this position, such as an oncoming vehicle threatening to cross the centerline.
Lane position changes continually depending on the road surface, other drivers, and your angle of view.

Loud Pipes

Basic science says that sound is not a reliable source of information. Sure, loud pipes increase the likelihood that drivers will know you are in the vicinity, but don’t be fooled into thinking that sound will help a driver locate where you are in traffic. This is why installing loud pipes is not a great strategy for increasing safety.
A much more reliable strategy is to be more visible. A driver who sees you and is able to accurately judge your speed and distance is much less likely to pull out in front of you. The importance of using strategies for being seen cannot be overemphasized. Unfortunately, too many riders don’t seem to understand this.

There are lots of other tips that are important for surviving on a motorcycle like don’t ride drunk or stoned, be attentive, etc. But. if you can follow these two strategies I outlined, you are well on your way to making it home at the end of a great day of riding.

OK. Now it’s your turn.

I know you’ve been chompin’ at the bit to tell the world what you think is the most important tip for surviving. So, let’s hear your comments.
submit to reddit

Please Donate to Keep the Articles Coming

If you liked this article and the many other articles on this site, please toss a buck or five into the hat. It’s greatly appreciated!

    • Click the PayPal “Pay Now” button.
    • Then indicate quantity in $2.00 increments. – Example: put “2” in “QUANTITY” field to donate $4.00, “3” for a $6.00 donation, etc.

Why $2.00? Due to the PayPal fee structure, a $2.00 donation is significantly more beneficial compared to a $1.00 donation.

Thank You!




Check out these posts:

How Can I help You? Online Coaching NOW AVAILABLE
Stay Informed: Subscribe NOW!
Trianing-Tours_LandingBe a Better Rider: Sign Up for Personal Training with Ken
Support Riding in the Zone: Buy a book
Support Riding in the Zone: Buy products from Twisted Throttle & Amazon
Twisted_Affiliate-Interphone-widget
Twisted_Affiliate-Interphone-widget